ASIX PIC-TOOLS

ASIX FORTE PROGRAMMER

€ 298,00

Tools for development, production and service FORTE is a very fast and flexible High-Speed USB In-Circuit Serial programmer for a wide range of popular components - microcontrollers, serial EEPROM and Flash memory chips, CPLDs and others. FORTE is equipped with an effective overcurent and overvoltage protection. The programmer is powered from USB and it is able to provide the supply voltage for the programmed device in range from 1.8 to 5.5 V or it can work with the externally powered target application. Software for FORTE works under Windows and Linux. Features Very fast programmer (30 MHz out, 15 MHz in/out) Controlled and powered by USB 2.0 High Speed (480 Mbps) Embedded processor for fast execution of complex operations Both synchronous and asynchronous programming algorithms supported, JTAG support Supported voltage range 1.8 to 5.5 V without any additional accessories Able to supply the voltage from 1.8 to 5.5 V to the external target application Programming interface offers 8 inputs/outputs with individually configurable pull-up/down resistors Built-in fast hardware I/O protection which works independently on the PC software Overcurrent protection on supply and programming voltage sources VDD pin overvoltage protection GO button makes repetitive operations easy and quick Wide range of supported devices, new software versions with new devices support are freely available from ASIX website RoHS compliant Command line and Windows messages support Works under Windows XP/Vista/7/8/8.1/10 (both 32 and 64 bit versions) and Linux (using Wine)

ASIX PRESTO PROGRAMMER

€ 146,00

PRESTO - Veloce e flessibile programmatore USB   Tools for development, production and service PRESTO is a powerful, very fast and cost effective In-Circuit Serial programmer for a wide range of popular components - microcontrollers, serial EEPROM and Flash memory chips, CPLDs and others. PRESTO operates on a USB port and requires no external power supply. Features Wide range of supported devices: Microcontrollers by Microchip, Atmel, Texas Instruments, Cypress and Cyan, ARM-based MCUs, serial EEPROM & Flash memories by various manufacturers, FPGA and CPLD devices by Xilinx, Altera and Lattice, ... Very fast operation Controlled and powered by USB Target application voltage 3 to 5 V Overcurrent and overvoltage protection GO button RoHS compliant New enclosure since April 2010 Advanced software for Windows XP/Vista/7/8/8.1/10 (both 32 & 64 bit) and Linux (using Wine)

SPINET

€ 20,00

Ethernet to SPI Interface Module   SPINET is a module based on ENC28J60 Ethernet controller by Microchip. It provides easy connection of any microcontroller like Microchip PIC or Atmel AVR to an Ethernet network. SPINET contains 10BASE-T physical layer (PHY) including RJ45 connector with galvanic insulation and media access control logic (MAC). The heart of SPINET - the ENC28J60 chip - is an IEEE 802.3 compliant stand-alone Ethernet controller. It supports half duplex and full duplex operation at 10 Mb/s and it is equipped by 8 KB of dual port SRAM for incoming and outgoing data. Besides of other features it includes hardware engine for copying blocks of memory and checksum calculation in one's complement arithmetics (IP checksum) and CRC. It connects to an external microcontroller by SPI interface which can be easily implemented in any microcontroller and requires only 4 or 5 signals. The module is powered by single power supply - either +3.3 V or +5 V. All module inputs are LVTTL and are 5 V tolerant. All outputs are doubled - they are available in 3.3 V levels (connected directly to ENC28J60) and, if 5 V power supply is used, also in 5 V levels. This is necessary for AVR microcontrollers operated on 5 V which have CMOS input levels and cannot reliably work with 3.3 V signals. Two LED indicators on the RJ45 connector help user to monitor the Ethernet activity. Four mounting holes allow for firm mechanical fixation of the SPINET module in user's equipment. SPI interface is connected to the open holes which allow for flexible connection of the cable or 2.54 mm/0.1 inch header (top/bottom, straight/right angle). An example program in C is available royalty free. It is written for the PVK40 development board (optional accessory SPINET4PVK recommended) with PIC18F458 but this can be easily modified for other microcontrollers. FEATURES 10BASE-T physical layer, full duplex or half duplex Including RJ45 connector with galvanic insulation Two LED indicators Media access controller (MAC) 8 KB of buffers for reception and transmission Hardware assisted checksum calculation Power by 3.3 V or 5 V Outputs with both 3.3 V and 5 V levels 5 V tolerant inputs Mounting holes for firm mechanical fixation Example program in C  

HPRAVR

€ 12,00

ICSPCAB8 to AVR Connector Adapter for PRESTO and FORTE   HPRAVR is optional accessory for the PRESTO and FORTE programmers for programming of the AVR microcontrollers in an application with standard ISP10PIN connector. This connector is usually used on the boards with the AVR processors like STK500.

HPR3V3

€ 18,00

3.3 V Level Shifter for PRESTO.